网站公告:

产品中心

济南精拓流体设备有限公司

电话:0531-69951198

邮箱:jingtuolt@163.com

传真:0531-69951198

地址:济南市历城区西周南路9号

网址:

网站公告

当前位置:首页 - 网站公告 - 高压空气增压泵安装必备步

高压空气增压泵安装必备步骤介绍

发布时间:2018-01-04 16:13:39   发布人:
1.高压空气增压泵的安装
Installation of 1. high pressure air booster pump
空气增压阀标配有两个开槽安装支架,增压阀可以安装在任意位置,推荐位置为垂直方向,每台售出增压阀都会附带图纸,标注所需的各种尺寸。
The air booster valve is equipped with two slotting mounting brackets. The booster valve can be installed at any location, and the recommended position is vertical. Every booster valve will be attached with drawings, indicating the required sizes.
2.预增气源连接
2. yejiyuzeng source connection
高压空气增压泵泵体上都标注“进口”,且图纸上都标有端口尺寸及型号。预增气体一定要纯净,气体介质若有杂志可能会损坏高压元件,导致增压阀运行故障,所以建议大家在增压阀进气口安装过滤装置。
The high pressure air pressurized pump body is marked "import", and the drawings are marked with the size and model of the port. By the gas must be purified, the gas medium if the magazine may damage the high-voltage components, leading to operational failure pressure increasing valve, it is recommended that you install filtering device in the booster valve inlet.
3.气源的连接
Connection of 3. gas sources
供气回路的安装时过滤/调压阀需尽量开进增压阀。进气口端口为G1/4”,阀体上标注为”驱动气口“,管径为1/2”,如果管径较小,增压阀就不可以以最大流量运行。过滤调压需按照名称顺序链接,靠近增压阀。
When the gas supply loop is installed, the filter / pressure regulating valve should be put into the pressurized valve as far as possible. The inlet port is G1/4, and the valve body is marked as a "drive air port" with a diameter of 1/2. If the pipe diameter is small, the booster valve can't run at the maximum flow rate. Filter pressure need to be linked in the name order, close to the turbocharger.
 气体增压泵
4.消声器
4. muffler
消声器的使用时用来降低增压阀运行时的噪音,保证运行环境的安静。排气口端口为G1/2”,标记为“出气口”。
The use of the muffler is used to reduce the noise of the operation of the pressurized valve, and to ensure the quiet of the operating environment. The port port is G1/2 ", marked as" air outlet ".
5.高压气体出口的连接
5. connection of high pressure gas outlet
在增压阀的配图上标有端口尺寸及型号,增压阀阀体上标注为“出口”,此为高压出口,所以连接时需要特别谨慎小心,连接件需要大于最大输出压力。
Port sizes and models in Figure booster valve superscript, booster valve on the valve body labeled as "export", this is the high pressure outlet, so the connection need to be cautious, connections need to be bigger than the maximum output pressure.
6.高压空气增压泵的启动
The start of 6. high pressure air booster pump
⑴在打开增压阀的进气开关之前,使用调节减压阀将气压调到“0”PSI
In the switch before the intake pressure valve, regulating valve pressure will be transferred to the "0" PSI
⑵确保所有的连接口及所有元件及安装。
The connection port and ensure all all the components and installation.
⑶将减压阀缓慢调节至增压阀开始启动,正常情况下增压阀在15-20PSI压力下气动。
The valve will slowly adjust to the pressure valve is started, under normal circumstances, the pressure valve under the pressure of 15-20PSI pneumatic.
⑷完成1到3步骤后,调节泵的供气气压直达到系统所需输出压力为止。
The completion of the 1 to 3 steps, gas pressure regulating pump system to direct the desired output pressure.

13188935873

qq

免责声明: 本站资料及图片来源互联网文章,本网不承担任何由内容信息所引起的争议和法律责任。所有作品版权归原创作者所有,与本站立场无关,如用户分享不慎侵犯了您的权益,请联系我们告知,我们将做删除处理!